ProSoft Technology ProLinx-HART Spezifikationen Seite 37
- Seite / 119
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Configure the Gateway HART ♦ ProLinx Gateway
Driver Manual HART Master
ProSoft Technology, Inc. Page 37 of 119
July 7, 2009
3.4.12 Swap Code
0, 1, 2, 3
This parameter defines the byte order of each four-byte group of data received.
This parameter is helpful when dealing with floating-point or other multi-register
values, as there is no standard byte order for storing these data types. The
following table describes the values and their associated operations:
Swap Code Description
0 None - No Change is made in the byte ordering (1234 = 1234)
1 Words - The words are swapped (1234=3412)
2
Words & Bytes - The words are swapped then the bytes in each word are
swapped (1234=4321)
3 Bytes - The bytes in each word are swapped (1234=2143)
3.4.13 Use Long
0 or 1
This parameter defines if the command will be executed with short or long
address. If the value is "0", then the configured command will be executed using
the Short Address specified. If the value is "1" then the specified Short Address
will be used only to ask for the long address and that will be used to execute the
configured command.
3.4.14 Enable DB Address
0 to 3999
This field specifies the internal database register to be used to enable the
execution of a command. This parameter is only used if "Enable" is "4" or "5". If
the value of this database register is "-1", then the command will be executed,
otherwise it will not. If the "Enable" value is "5", then after the successful
execution of the command this value will become "0"
3.4.15 Done DB Address
-1 to 3999
This field specifies the internal database register to be used to signal the
successful execution of a command. When a command is successfully executed
a "-1" is written to this register. This "Done DB Address" can be shared with the
"Enable DB Address" of another command to do a chained command execution.
3.4.16 Write DB Address
-1 to 3999
- DRIVER MANUAL 1
- All ProLinx® Products 2
- Your Feedback Please 3
- Contents 5
- 1 Start Here 7
- 1.2 Package Contents 8
- 1.5.1 Using the Help System 10
- 2 Functional Overview 11
- Port Label Function 12
- Channel 6 Hart Port 5 12
- Channel 7 Hart Port 6 12
- Channel 8 HART Port 7 12
- 2.3.2 Auto-Polling 15
- 2.3.3 HART Command List 23
- 3 Configure the Gateway 25
- EFAULT PROJECT and 26
- 3.1 Module Entries 27
- 3.3 [HART PORT x] 28
- 3.3.1 Enabled 28
- 3.3.2 Preambles 29
- 3.3.3 Primary Master 29
- 3.3.4 Retry Count 29
- 3.3.5 DB Address Status 29
- 3.3.6 Command Count 29
- 3.3.7 Auto-Poll Code 30
- 3.3.8 Auto-Poll DB Address 30
- 3.3.9 Auto-Poll Swap Float 30
- 3.3.10 Max Device Count 30
- 3.4 [HART PORT x COMMANDS] 31
- 3.4.1 Command List Overview 31
- 3.4.3 Enable 32
- 3.4.4 Float DB Address 33
- 3.4.5 Poll Interval 33
- 3.4.6 FP Word Count 33
- 3.4.7 Swap Code 33
- 3.4.8 Short Address 34
- 3.4.9 Function Code 34
- 3.4.10 Int. DB Address 36
- 3.4.11 Int Word Count 36
- 3.4.12 Swap Code 37
- 3.4.13 Use Long 37
- 3.4.14 Enable DB Address 37
- 3.4.15 Done DB Address 37
- 3.4.16 Write DB Address 37
- 3.4.17 Swap Code 38
- 3.4.18 Byte Count 38
- 3.4.19 Fixed Data 38
- 3.5 Data Map 39
- 3.5.2 From Address 40
- 3.5.3 To Address 40
- 3.5.4 Register Count 40
- 3.5.5 Swap Code 40
- 3.5.6 Delay Preset 41
- OWNLOAD dialog box opens 42
- OWNLOAD button 42
- 4 Error/Status Data 43
- 4.6.2 Slave List Status 47
- 4.7 Module Error Codes 47
- 4.7.1 Protocol Error Codes 47
- 5 Reference 51
- Word High Byte Low Byte 55
- 0 STATUS WORD 55
- 1 Polling Address 0 55
- COMMAND 12 - Read Message 56
- COMMAND 17 - Write Message 61
- COMMAND 39 - EEPROM Control 70
- COMMAND 43 - Set PV Zero 74
- COMMAND 44 - Write PV Units 75
- COMMAND 45 - Trim DAC Zero 76
- COMMAND 46 - Trim DAC Gain 77
- 1 Transfer Function Code 0 78
- Type Network Power Supply 94
- A Required 94
- B Required 94
- C Must not be used 94
- 5.4 HART Status Data Map 102
- 5.4.2 Port 0 Command Errors 102
- 5.4.4 Port 1 Command Errors 103
- 5.4.5 Port 2 Data 103
- 5.4.9 Port 6 Data 104
- 5.4.10 Port 7 Data 104
- 5.4.6 Port 3 Data 104
- 5.4.7 Port 4 Data 104
- 5.4.8 Port 5 Data 104
- 5.5 Module Status Values 105
- 5.5.1 Normal Operation 105
- 5.5.2 Interface Crash Codes 105
- 5.5.3 Fatal Crash Codes 105
- 5.5.4 Peer Status Codes 106
- 5.6 Module Status Data Map 107
- 5.6.2 HTTP Port 80 Status 107
- 5.6.3 SNTP Client Status 107
- In This Chapter 111
- 6.2.1 All Product Returns: 112
- 6.3 LIMITED WARRANTY 113
- 6.3.8 No Other Warranties 116
- 6.3.9 Allocation of Risks 116
- Write DB Address • 37 119
- Your Feedback Please • 3 119
Verwandte Produkte und Handbücher für Gateways / Controller ProSoft Technology ProLinx-HART
(86 Seiten)Chief FCABX18_36 manuales
Manuales del propietario y guías del usuario para Hardware Chief FCABX18_36.
Ofrecemos 1 manuales en pdf Chief FCABX18_36 para descargar gratis por tipos de documentos: Manual de usuario
Kommentare zu diesen Handbüchern