Prosoft-technology MVI71-MNET Bedienungsanleitung Seite 12
- Seite / 109
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
MVI71-MNET ♦ PLC Platform Start Here
Modbus TCP/IP Interface Module User Manual
Page 12 of 109 ProSoft Technology, Inc.
June 23, 2009
1.4 Setting Jumpers
The Setup Jumper acts as "write protection" for the module’s flash memory. In
"write protected" mode, the Setup pins are not connected, and the module’s
firmware cannot be overwritten. Do not jumper the Setup pins together unless
you are directed to do so by ProSoft Technical Support.
The following illustration shows the MVI71-MNET jumper configuration.
Note: If you are installing the module in a remote rack, you may prefer to leave the Setup pins
jumpered. That way, you can update the module’s firmware without requiring physical access to
the module.
1.5 Install the Module in the Rack
If you have not already installed and configured your PLC processor and power
supply, please do so before installing the MVI71-MNET module. Refer to your
Rockwell Automation product documentation for installation instructions.
Warning: You must follow all safety instructions when installing this or any other electronic
devices. Failure to follow safety procedures could result in damage to hardware or data, or even
serious injury or death to personnel. Refer to the documentation for each device you plan to
connect to verify that suitable safety procedures are in place before installing or servicing the
device.
After you have checked the placement of the jumpers, insert MVI71-MNET into
the PLC™ chassis. Use the same technique recommended by Rockwell
Automation to remove and install PLC modules.
Warning: This module is not hot-swappable! Always remove power from the rack before
inserting or removing this module, or damage may result to the module, the processor, or other
connected devices.
- MVI71-MNET 1
- Warnings 2
- Battery Life Advisory 3
- Your Feedback Please 3
- Contents 5
- 1 Start Here 9
- 1.2 Package Contents 10
- 1.4 Setting Jumpers 12
- DF1 DEVICES 17
- 2 Module Configuration 19
- 2.2 Module Data 22
- 2.3 Status Data 22
- 2.4 User Data 22
- 2.5 Event Command Data 23
- 2.6 Modbus Message Data 23
- 2.7.1 Set Up the Project 24
- 2.7.2 Set Module Parameters 26
- 2.7.3 [Module] 27
- 2.7.4 [Static ARP Table] 29
- 2.7.5 [MNET Client x] 30
- 2.7.7 [MNET Servers] 37
- 2.7.8 Ethernet Configuration 39
- OWNLOAD button 40
- OWNLOAD dialog 40
- 3 Ladder Logic 41
- In This Chapter 43
- 4.1.1 Required Hardware 43
- IAGNOSTICS 44
- on your keyboard 45
- 4.1.3 Main Menu 46
- 4.1.4 Modbus Database View 49
- 4.1.5 Command List Menu 51
- 4.1.6 Network Menu 52
- 4.2 LED Status Indicators 53
- 4.2.3 Troubleshooting 55
- 5 Reference 57
- 5.2 Functional Overview 59
- 5.2.1 General Concepts 59
- 5.3 Cable Connections 78
- 5.3.1 Ethernet Connection 78
- 6.2.1 All Product Returns: 100
- 6.3 LIMITED WARRANTY 101
- 6.3.8 No Other Warranties 105
- 6.3.9 Allocation of Risks 105
Verwandte Produkte und Handbücher für Relais Prosoft-technology MVI71-MNET
(199 Seiten)Chief FCABX18_36 manuales
Manuales del propietario y guías del usuario para Hardware Chief FCABX18_36.
Ofrecemos 1 manuales en pdf Chief FCABX18_36 para descargar gratis por tipos de documentos: Manual de usuario
Kommentare zu diesen Handbüchern