ProSoft Technology ProTalk PTQ-104C Bedienungsanleitung Seite 174
- Seite / 195
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Reference PTQ-104S Rev2 ♦ Quantum Platform
User Manual IEC 60870-5-104 Server for Quantum
Page 174 of 195 ProSoft Technology, Inc.
February 22, 2013
9.5 Group Codes
One aspect of the point configuration database that leads to confusion is the
group definition field, which assigns each point to one or more interrogation
groups. Use of interrogation groups permits the controlling unit to interface with a
specific set of data. Refer to the IEC 60870-5-104 standard for a full discussion
of interrogation groups. A specific group, Periodic data group, reports data points
on a set frequency. The frequency is set in the Cyclic Data Transmission
parameter in the configuration file. Remember that a point can be assigned to
more than one group.
Group Code
Description
0x00000001
Interrogated by general interrogation (station or global)
0x00000002
Interrogated by group 1 interrogation
0x00000004
Interrogated by group 2 interrogation
0x00000008
Interrogated by group 3 interrogation (See Note 1, below)
0x00000010
Interrogated by group 4 interrogation
0x00000020
Interrogated by group 5 interrogation
0x00000040
Interrogated by group 6 interrogation
0x00000080
Interrogated by group 7 interrogation
0x00000100
Interrogated by group 8 interrogation
0x00000200
Interrogated by group 9 interrogation
0x00000400
Interrogated by group 10 interrogation
0x00000800
Interrogated by group 11 interrogation
0x00001000
Interrogated by group 12 interrogation
0x00002000
Interrogated by group 13 interrogation
0x00004000
Interrogated by group 14 interrogation
0x00008000
Interrogated by group 15 interrogation
0x00010000
Interrogated by group 16 interrogation
0x00020000
Interrogated by general counter request
0x00040000
Interrogated by group 1 counter request
0x00080000
Interrogated by group 2 counter request
0x00100000
Interrogated by group 3 counter request
0x00200000
Interrogated by group 4 counter request
0x40000000
Disable event scanning of this point
0x80000000
Periodic/cyclic data returned from unit
Note 1: Group 3 interrogation also returns the parameter data (ASDU 110 – threshold, low limit
and high limit) for all monitored measured points.
If the highest bit (bit 31) is set, data will be produced by the driver for the
specified point at the rate set for periodic data generation. Bit 30 (0x40000000)
enables scanning of this point for event generation. If the bit is clear and the data
type is set for scanning, events will be generated for the point. If the bit is set,
events will not be generated for the point. This feature can be used to select
which points will generate events for the controlling station and can get rid of
event data that is not important to the application.
- PTQ-104S Rev2 1
- Your Feedback Please 2
- Information for ProTalk 3
- Product Users 3
- Warnings 3
- Important Notice: 4
- Contents 5
- 1 Start Here 11
- 1.1.1 Package Contents 12
- 1.1.2 Quantum Hardware 12
- 1.1.3 PC and Software 13
- THERNET CONFIGURATION icon 18
- DIT dialog box 19
- 2.1 Create a New Project 22
- EW DEVICE 23
- to continue 23
- 2.3 Build the Project 25
- ROGRESS dialog box 29
- TART / PROGRAMS / CONCEPT 32
- MODCONNECT TOOL 32
- 3.2 Creating a New Project 33
- dialog box 36
- to save the settings 38
- ES to confirm the settings 38
- PECIALS 39
- PECIALS dialog box 39
- 3.5 Saving the Project 40
- ODULE as PTQ: 46
- 5 Module Configuration 49
- 5.1.2 Set Module Parameters 53
- ILE menu, and choose PRINT 54
- 5.2.1 Read Register Start 55
- 5.2.2 Read Register Count 55
- 5.2.3 Write Register Start 55
- 5.2.4 Write Register Count 55
- 5.2.5 3X Register Start 55
- 5.2.6 4X Register Start 56
- 5.2.7 Module Name 56
- 5.2.8 Error Offset 56
- 5.3 Backplane Data Exchange 56
- 5.3.3 Event Messages (9958) 65
- 5.4 [SNTP CLIENT] 69
- 5.4.1 NTP Server IP Address 70
- 5.4.2 Time Zone 70
- 5.4.4 Database Register 71
- 5.5 [I104S] Section 71
- 5.6.1 Use IP List 72
- 5.6.2 Override StartDT 72
- O (0) or YES (1) 73
- to 1000, default value = 30 73
- 5.6.10 Time DB Offset 74
- 5.6.11 Error Offset 74
- seconds 75
- 5.6.19 Use ACTTERM with step 76
- 5.6.20 Event Scan Delay 76
- 5.6.22 Set Priority Queues 76
- 5.6.23 Cyclic Set IV Time 77
- 5.6.24 IV Check Delay Time 78
- 5.6.25 IV Fail Count 79
- 5.6.26 Scan Events 79
- 5.6.27 Time Type 80
- 5.6.28 Use Recent 80
- 5.7.1 Short Pulse Time 82
- 5.7.2 Long Pulse Time 82
- 5.7.5 Point Count 83
- 5.7.6 Sequence Flag 84
- 5.7.7 Parameter Offset 85
- ADDRESS value 87
- 5.24 Group Codes 92
- To Download the Project File 96
- OWNLOAD FROM PC TO 97
- OWNLOAD dialog box 97
- OWNLOAD button 97
- OWNLOAD dialog 100
- 7 Hot Standby Support 101
- 7.1 Hot Standby Overview 102
- 7.1.3 System Components 103
- Standby with Unity Systems 104
- Example #1 105
- 7.2.1 Overview 106
- In This Chapter 111
- 8.1.1 Required Hardware 112
- IAGNOSTICS 113
- IAGNOSTICS dialog box 113
- to open the Main Menu 114
- 8.1.3 Navigation 115
- 8.1.4 Main Menu 116
- to return to the Main Menu 120
- 8.2 LED Indicators 121
- 8.2.2 Error Status Table 122
- 9 Reference 123
- 9.1 Product Specifications 124
- 9.1.1 Standards 124
- 9.2.1 Module Address 127
- 9.2.3 Using Monitor Points 132
- Example - Mode A 138
- Example (C_SC_NA) 144
- 9.2.5 Data Communication 150
- Example: 151
- 9.2.6 Events 156
- Example - Event Priority 167
- 9.2.7 Sequence Flag 169
- 9.3 Cable Connections 170
- 9.3.1 Ethernet Connection 170
- 9.4 Error Status Table 171
- 9.5 Group Codes 174
- 9.6.1 System or device 175
- 9.6.2 Application Layer 175
- Point Number 186
- Database Address 186
- Group Assignment 186
- Default Deadband 187
- 9.7.4 C_RC_NA_1 Form 189
- 10.2 Warranty Information 192
Verwandte Produkte und Handbücher für Server ProSoft Technology ProTalk PTQ-104C
(306 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern